Array Support Library (ASL)/Array Policy Module (APM) Details
VRTSFJTSYe8k [Download] - 60 K Sign in if you want to rate this ASL/APM.

 Basic information

Library name: libvxFJTSYe8k
Library version: vm-5.0-rev-3
Package name: VRTSFJTSYe8k
Package description: Array Support Library for Fujitsu ETERNUS DX8000/DX400 and ETERNUS8000/4000
Package version: 5.0-rev-3
Supported product versions:
  • 5.0
  • 5.0.1
Embedded in VxVM?: No
Supported platforms:
  • HP-UX 11i v3 (11.31)
TechNote: 338353
Popularity: 426 viewed  5 downloaded
Download size: 60K
Checksum: 1642514882
Release date: N/A

 Supported Arrays and Modes

  • ETERNUS DX400 series, ETERNUS DX410, ETERNUS DX440, ETERNUS DX8000 series, ETERNUS DX8100, ETERNUS DX8400, ETERNUS DX8700, ETERNUS4000 Model 300, ETERNUS4000 Model 400, ETERNUS4000 Model 500, ETERNUS4000 Model 600, ETERNUS4000 series, ETERNUS8000 Model 1100, ETERNUS8000 Model 1200, ETERNUS8000 Model 2100, ETERNUS8000 Model 2200, ETERNUS8000 Model 700, ETERNUS8000 Model 800, ETERNUS8000 Model 900, ETERNUS8000 series
Supported mode: A/A

 Readme file  [Save As...]

This TechFile provides information about the Array Support Library (ASL) for Fujitsu ETERNUS4000, ETERNUS8000, ETERNUS DX400 and ETERNUS DX8000 Series Arrays (Active/Active) on Veritas Volume Manager (tm) 5.0, 5.0MPx for HP-UX 11iv2 and 5.0, 5.0.1 for HP-UX 11iv3 For general information about ASLs, refer to Solution 249446 (link in the Related Documents section below). Package Name: VRTSFJTSYe8k Package Description: Array Support Library for Fujitsu ETERNUS DX8000/DX400 and ETERNUS8000/4000 Package Version: 5.0-rev-3 Supported versions of Veritas Volume Manager: HP-UX 11iv2: 5.0, 5.0MP1, 5.0MP2 HP-UX 11iv3: 5.0, 5.0.1 Supported Arrays: Fujitsu ETERNUS4000 Series, Fujitsu ETERNUS8000 Series, Fujitsu ETERNUS DX400 Series, Fujitsu ETERNUS DX8000 Series Supported Mode: Active/Active Installation Instructions: Note: If the previous version of this ASL is installed in your system, please uninstall it before installing this version. 1. Create a directory to store the ASL package: # mkdir /tmp/asl # cd /tmp/asl 2. At the bottom of this TechFile, click on Download Now to download the ASL package 3. After downloading VRTSFJTSYe8k_5.0_v3_HPUX.tar_338353.gz, verify checksum of the file as follows: # cksum VRTSFJTSYe8k_5.0_v3_HPUX.tar_338353.gz 1642514882 61115 VRTSFJTSYe8k_5.0_v3_HPUX.tar_338353.gz 4. Uncompress the file and extract the package: # gunzip VRTSFJTSYe8k_5.0_v3_HPUX.tar_338353.gz # tar xvf VRTSFJTSYe8k_5.0_v3_HPUX.tar_338353 5. Before adding any ASL packages, ensure Veritas Volume Manager is installed and enabled: # vxdctl mode mode: enabled 6. Attach the disk array and reboot. Then, to enable vxconfigd to claim E8000 as JBOD when ASL is not being used, execute the following commands: # vxddladm rmjbod vid="FUJITSU" # vxddladm addjbod vid="FUJITSU" pid="E8000" offset=44 length=4 # vxddladm listjbod VID PID Opcode Page Code Page Offset SNO length Policy ========================================================================== ... FUJITSU E8000 18 -1 44 4 Disk 7. ASL Installation: # swinstall -s `pwd` VRTSFJTSYe8k Note: The package name and the above installation instruction is common for both 11iv2 and 11iv3. 8. After the package is installed, you must execute the vxdctl enable command to claim the disk array as an ETERNUS DX8000/DX400 or ETERNUS8000/4000 array: # vxdctl enable Note: In some cases, it has been reported that the installation of the ASL does not take effect, and the vxdctl enable command does not claim the enclosure and devices. In such cases, you can execute the vxconfigd -k command in addition to vxdctl enable. 9. After running vxdctl enable, run the vxddladm listsupport and vxddladm listversion commands and verify the output as follows: # vxddladm listsupport libname=libvxFJTSYe8k.sl ATTR_NAME ATTR_VALUE ================================================================================================= LIBNAME libvxFJTSYe8k.sl VID FUJITSU PID E4000, E8000, ETERNUS_DX400 ETERNUS_DX8000 ARRAY_TYPE A/A ARRAY_NAME FJ_E4000, FJ_E8000, FJ_DX400 FJ_DX8000 # vxddladm listversion libname=libvxFJTSYe8k.sl libvxFJTSYe8k.sl has version string: vm-5.0-rev-3. VXVM version: 5.0 Package Information: # swlist VRTSFJTSYe8k # Initializing... # Contacting target "vvrias09"... # # Target: vvrias09:/ # # VRTSFJTSYe8k 5.0-rev-3 Array Support Library for Fujitsu ETERNUS DX8000/DX400 and ETERNUS8000/4000 VRTSFJTSYe8k.ASL_FILES 5.0-rev-3 Array Support Library for Fujitsu ETERNUS DX8000/DX400 and ETERNUS8000/4000

Read and accept Terms of Service