This TechFile provides information about the array support library for Fujitsu ETERNUS4000, ETERNUS8000, ETERNUS DX400 and ETERNUS DX8000 series arrays (Active/Active) on Veritas Volume Manager (tm) 5.0 and 5.0MPx for Linux (RHEL/SLES)

For general information about ASLs, refer to TechNote 249446 (link in the Related Documents section below).

Package Name: VRTSFJTSYe8k
Package Description: Array Support Library for Fujitsu ETERNUS DX8000/DX400 and ETERNUS8000/4000
Package Version: 2.0
Supported versions of Veritas Volume Manager: 5.0, 5.0 MP1, 5.0 MP2, 5.0 MP3
Supported Arrays: Fujitsu ETERNUS4000 Series, Fujitsu ETERNUS8000 Series, Fujitsu ETERNUS DX400 Series, Fujitsu ETERNUS DX8000 Series
Supported Mode: Active/Active

Installation Instructions:
1. Create a directory to download the ASL
# mkdir /tmp/asl
# cd /tmp/asl

2. At the bottom of this TechFile, click on Download Now to download the ASL package

3. After downloading VRTSFJTSYe8k_v2_Linux_50.tar_338462.gz, verify checksum of the file
# cksum VRTSFJTSYe8k_v2_Linux_50.tar_338462.gz
1960565644 12679 VRTSFJTSYe8k_v2_Linux_50.tar_338462.gz

4. Uncompress the file and extract the rpm package
# gunzip VRTSFJTSYe8k_v2_Linux_50.tar_338462.gz
# tar xvf VRTSFJTSYe8k_v2_Linux_50.tar_338462

5. Before adding any ASL package, ensure Veritas Volume Manager is installed and enabled
# vxdctl mode
mode: enabled

Note: Following are installation instructions for RHEL and common for both RHEL and SLES.
6. ASL Installation:
# rpm -ivh VRTSFJTSYe8k-5.0-1.2_RHEL.i686.rpm
Preparing...                ########################################### [100%]
  1:VRTSFJTSYe8k           ########################################### [100%]
Adding the entry in supported arrays
Loading The Library

7. After the package is installed, you must run the vxdctl enable command to claim the disk array as Fujitsu array
# vxdctl enable

Note: In some cases, it has been reported that the installation of the ASL does not take effect, and the vxdctl enable command does not claim the enclosure and devices. In such cases, you can execute the vxconfigd -k command in addition to vxdctl enable.

8. After running vxdctl enable, run the vxddladm listsupport and vxddladm listversion command and verify the output
# vxddladm listsupport libname=libvxFJTSYe8k.so
ATTR_NAME           ATTR_VALUE
=================================================================================================
LIBNAME             libvxFJTSYe8k.so
VID                 FUJITSU
PID                 E4000, E8000, ETERNUS_DX400
                   ETERNUS_DX8000
ARRAY_TYPE          A/A
ARRAY_NAME          FJ_E4000, FJ_E8000, FJ_DX400
                   FJ_DX8000

# vxddladm listversion libname=libvxFJTSYe8k.so
libvxFJTSYe8k.so has version string: vm-5.0-rev-3. VXVM version: 5.0

ASL Package Information:
# rpm -qil VRTSFJTSYe8k-5.0-1.2_RHEL
Name        : VRTSFJTSYe8k                 Relocations: (not relocatable)
Version     : 5.0                               Vendor: Symantec Software Corporation Inc.
Release     : 1.2_RHEL                      Build Date: Wed 09 Sep 2009 05:03:28 PM IST
Install Date: Fri 11 Dec 2009 11:58:01 AM IST      Build Host: vmlx11.veritas.com
Group       : System/Data Storage           Source RPM: VRTSFJTSYe8k-5.0-1.2_RHEL.src.rpm
Size        : 10281                            License: Copyright (c) 1990-2009 Symantec.  ALL RIGHTS RESERVED.  THIS SOFTWARE IS THE PROPERTY OF AND IS LICENSED BY Symantec, AND/OR ITS SUPPLIERS.
Signature   : (none)
Packager    : linuxvm-pkgr@veritas.com
URL         : http://www.symantec.com/
Summary     : Array Support Library for Fujitsu ETERNUS DX8000/DX400 and ETERNUS8000/4000
Description :
Array Support Library for Fujitsu ETERNUS DX8000/DX400 and ETERNUS8000/4000
/etc/vx/aslkey.d
/etc/vx/aslkey.d/libvxFJTSYe8k.key.2
/etc/vx/lib/discovery.d
/etc/vx/lib/discovery.d/libvxFJTSYe8k.so.2