This TechFile provides information about the Array Support Library (ASL) for Fujitsu ETERNUS3000 and ETERNUS4000 Model 80/100 arrays on Solaris.

For general information about ASLs, see TechNote 249446 (link in the Related Documents section of this TechFile)

Package name: Fujitsu ETERNUS3000 Series and ETERNUS4000 Model80/100 Array Support Library for Volume Manager 5.X
Package version: 5.0,REV=2.0_2008.09.11.04.04
Supported versions of Veritas Volume Manager (tm): 5.0 MP1 Rolling Path 3 and later
Supported arrays: Fujitsu ETERNUS3000 (Active/Passive-Group (A/P-G))
                           Fujitsu ETERNUS4000 Model 80/100 (Active/Passive-Group (A/P-G))

Note: This TechNote fixed an issue according to ETrack Incident 1388360 and replaced TechNote 290800.

Note: The ETERNUS3000 and ETERNUS4000 Model 80/100 array must be configured to exhibit A/P-G characteristics and must support SCSI-III PGR. A firmware upgrade may be required for SCSI-III PGR support. For additional details on array configuration, contact Fujitsu Technical Support.

Note: To support ETERNUS3000 and ETERNUS4000 Model 80/100 array, Volume Manager 5.0 MP1 Rolling Path 3 is required.

At the bottom of this TechFile, click on Download Now to download the ASL package VRTSFJTSYe3k4ka_v2_SunOS_50_308415.tar.Z . Before adding any ASL package, ensure Veritas Volume Manager is installed and enabled:

# vxdctl mode
mode: enabled

Note: If installing on Solaris 9, then set LD_LIBRARY_PATH to /usr/lib. See TechNote 251706 for complete information (link in the Related Documents section of this TechFile)

After downloading VRTSFJTSYe3k4ka_v2_SunOS_50_308415.tar.Z , uncompress and extract the package:

# zcat VRTSFJTSYe3k4ka_v2_SunOS_50_308415.tar.Z  | tar xvf -

To install the package:

# pkgadd -d . VRTSFJTSYe3k4ka

After the package is installed, you must run the vxdctl enable command to claim the disk array as a FUJITSU array:

# vxdctl enable

After running vxdctl enable, you should see libvxFJTSYe3k4ka.so in the output of vxddladm listsupport:

# vxddladm listsupport | grep -i FUJITSU
libvxFJTSYe3k4ka.so  FUJITSU


# vxddladm listversion libname=libvxFJTSYe3k4ka.so
libvxFJTSYe3k4ka.so has version string: vm-5.0-rev-2. VXVM version: 5.0


For additional information about ASLs, see Installing an Array Support Library (ASL) Guide for Solaris, TechNote 249325 (link in the Related Documents section of this TechFile)

Package information:

# pkginfo -l VRTSFJTSYe3k4ka
  PKGINST:  VRTSFJTSYe3k4ka
     NAME:  Fujitsu ETERNUS3000 Series and ETERNUS4000 Model80/100 Array Support Library for Volume Manager 5.X
 CATEGORY:  system
     ARCH:  sparc
  VERSION:  5.0,REV=2.0_2008.09.11.04.04
  BASEDIR:  /etc/vx
   VENDOR:  Symantec
     DESC:  Fujitsu ETERNUS3000 Series and ETERNUS4000 Model80/100 Array Support Library for Volume Manager 5.X
   PSTAMP:  VERSION-5.0:5-September-2007
 INSTDATE:  Sep 11 2008 20:13
  HOTLINE:  800-342-0652
    EMAIL:  support@veritas.com
   STATUS:  completely installed
    FILES:        5 installed pathnames
                  3 shared pathnames
                  3 directories
                  2 executables
                 23 blocks used (approx)