Disk Group
|
Name of the disk group.
|
RLINK Name
|
Name of the RLINK.
|
Info
|
timeout, packet_size, record_id, latency high, low marks and bandwidth_limit.
|
State
|
Displays utility state of the RLINK - active, stale, etc.
|
synchronous, latencyprot, and srlprot
|
The current configuration settings for the replication mode, the latency mode, and SRL protection.
|
assoc
|
The RVG to which the RLINK is associated.
|
remote_host/IP_addr/port
|
The name of the remote host for the RLINK, its IP address, and the port number.
|
remote_dg
|
The name of the disk group on the remote system.
|
remote_dg_dgid
|
The disk group ID assigned when the disk group was created on the remote system.
|
remote_rvg_version
|
The rvg_version of the remote RVG.
|
remote_rlink
|
The name of the corresponding RLINK on the remote host.
|
remote_rlink_rid
|
The record_id of the corresponding RLINK on the remote host.
|
local_host/IP_addr/port
|
The name of the local host, its IP address, and the port number it uses for communication to the remote host.
|
protocol
|
The transport protocol used by the RLINK for communicating between the hosts. The protocol can be either UDP/IP or TCP/IP.
|
checkpoint
|
Displays the checkpoint only if the Primary RLINK is attached using the checkpoint or the Secondary RLINK has been restored using the checkpoint.
|
flags
|
See Interpreting RLINK flag settings.
|
autosync
|
The RDS is in the process of automatic synchronization.
|
attached
|
The RLINK is attached to the RVG.
|
can_sync
|
If the inconsistent and can_sync flags are set, there is enough information in the Secondary SRL volume to make the Secondary consistent again and capable of taking over.
|
cant_sync
|
The RLINK is inconsistent, and this Secondary needs a complete resynchronization before it can take over or replicate.
|
connected
|
The RLINK is connected to the corresponding RLINK on the remote host and replication can take place.
|
consistent
|
The state of the data volumes on the Secondary is suitable for takeover.
|
dcm_logging
|
DCM is in use, due to either autosync, failback sync, or an SRL overflow.
|
detached
|
The RLINK is stale and not taking part in replication.
|
disabled
|
The RLINK is not attached and is not replicating.
|
disconnected
|
The two RLINKs are not connected and are not replicating.
|
enabled
|
The RLINK is attached. If the connected flag is displayed, replication can take place. If the disconnected flag is displayed, replication is not taking place.
|
fail
|
An I/O error occurred while writing to a data volume on the Secondary.
|
inconsistent
|
The data in the Secondary volumes is not consistent and the Secondary cannot take over.
|
needs_recovery
|
State after an import or reboot. The vxrecover command clears this state.
|
primary_paused
|
The Primary RLINK has been paused and the RLINKs are not replicating.
|
resync_started
|
The resynchronization of the Secondary has been started.
|
resync_paused
|
The resynchronization has been started but is not currently active because of some problem.
|
secondary_config_err
|
There is a mismatch between the configuration of the volumes on the Primary and the Secondary - either a volume is missing on the Secondary or its length is not the same as that of the corresponding volume on the Primary.
|
secondary_log_err
|
An I/O error has occurred on the Secondary SRL; replication cannot continue until the SRL has been dissociated and a new one associated.
|
secondary_paused
|
The Secondary RLINK has been paused and the RLINKs are not replicating.
|