Home > Veritas Storage Foundation™ Volume Manager Manual Pages
[-t tasktag] [-U usetype] start volume
vxrelayout status volume
vxrelayout help | -H
The transformation of a volume or a plex must be initiated using the vxassist(1M) utility. vxassist creates necessary infrastructure and storage needed to perform the layout transformation and invokes vxrelayout internally to actually perform the transformation.
Note: The relayout operation internally generates unique data object names (for example, v2-Dp02) when it converts a volume to a specified destination layout.
Because vxrelayout depends on vxassist to do all the setup before a layout transformation can begin, the vxassist utility must be used to initiate any layout transformation. The vxtask(1M) utility can monitor the state of an ongoing transformation.
Because these transformations are time consuming (mainly depending on the volume size and chunk size), they can be interrupted because of a system crash, I/O failure, or the user voluntarily stopping the transformation process either by aborting the task associated with the transformation using vxtask or by killing the transformation process. It is not advisable to use kill -9 to stop the transformations. The vxrelayout utility can be used to continue or reverse a transformation process because of such interruptions.
Veritas Volume Manager responses to possible interruptions are:
If the user stops vxrelayout, then the transformation process can be reversed or continued by invoking vxrelayout manually.
Even though such a capability of direction change can be used ad infinitum, it has been provided with an objective to react to unforeseen situations. It is advisable that such direction changes are done with care.
The direction of a transformation can be determined using the status operation provided in the vxrelayout utility. This command will determine if any plex in the volume is being transformed and display its characteristics.
The second operand is the name of the topmost volume to which the plex undergoing relayout is attached. If there are multiple plexes in the volume and only one of them is being transformed, the vxrelayout utility will select the appropriate plex using the supplied volume name. It should be noted that there can only be one relayout operation happening in a volume at any instant of time. A specific disk group can be forced with -g diskgroup.
This operation can be applied only to disk groups with version 60 or above (see vxdg(1M)), and only to one disk group at a time. The supported storage layouts are:
See the Veritas Volume Manager Administrator's Guide for more information.
- Forces a continue or reverse of a layout transformation. This is considered potentially dangerous or questionable to use as using this flag may result in loss of data. This permits a limited set of operations that would otherwise be disallowed:
- It is possible that an I/O failure during a layout transformation caused some plexes to detach, If the user still wants to continue or reverse such a transformation, this flag will have to be used to tell vxrelayout to ignore the fact some plexes have failed. There is no guarantee that this operation will succeed.
- vxrelayout shrinks any existing file system on a volume if the layout transformation causes the volume size to decrease. If the user does not want vxrelayout to shrink the file system but wants to still perform the layout conversion, this flag must be used.
- -g diskgroup
- Specifies the disk group for the operation, either by disk group ID or by disk group name. By default, the disk group is chosen based on the name operands.
- -o useopt
- Passes in usage-type-specific options to the operation. A certain set of operations are expected to be implemented by all usage types:
- Reduces the system performance impact of copy operations. Copy operations are usually a set of short copy operations on small regions of the volume (normally from 16 kilobytes to 128 kilobytes). This option inserts a delay between the recovery of each such region. A specific delay can be specified with iodelay as a number of milliseconds; otherwise, a default is chosen (normally 250 milliseconds).
- Performs copy operations in regions with the length specified by size, which is a standard Veritas Volume Manager length number (see vxintro(1M)). Specifying a larger number typically causes the operation to complete sooner, but with greater impact on other processes using the volume. The default I/O size is 1 megabyte.
Note: These parameters can also be changed using the vxtask utility during an online relayout.
- Run the vxrelayout operation in the background.
- -t tasktag
- If any tasks are registered to track the progress of the operation, marks them with the tag tasktag. The tag specified by tasktag is a sequence of up to 16 alphanumeric characters.
- -U usetype
- Limits the operation to apply to this usage type. Attempts to affect volumes with a different usage type will fail.
- Displays information on vxrelayout usage.
See vxintro(1M) for a list of standard exit codes.
vxrelayout status homevol
Restart conversion of the volume homevol at a slow rate in the background (layout conversion having previously been stopped by using the pause keyword in vxtask):
vxrelayout -o slow,bg start homevol
Reverse conversion of the volume homevol (layout conversion having previously been stopped):
vxrelayout reverse homevol
Veritas Volume Manager Administrator's Guide
Last updated: 28 Jul 2003
Copyright ©2009 Symantec Corporation
All rights reserved.