vxfenadm - Manage SCSI-3 disk registrations and reservations for I/O fencing and display information on I/O fencing operations.
vxfenadm -s diskpath | -s all -f disk_filename
vxfenadm -G diskpath | -G all -f disk_filename
vxfenadm -R diskpath | -R all -f disk_filename
vxfenadm -a -k|K key -f disk_filename
vxfenadm -m -k|K key -f disk_filename
vxfenadm -n -k|K key -f disk_filename
vxfenadm -x -k|K key -f disk_filename
vxfenadm -p -k|K key -f disk_filename -v victim_node_key
vxfenadm -g diskpath | -g all -f disk_filename
vxfenadm -r diskpath | -r all -f disk_filename
vxfenadm -c -k|K key -f disk_filename
vxfenadm -i diskpath
vxfenadm -t diskpath
vxfenadm -d diskpath
The vxfenadm utility enables the vxfen driver to manage SCSI-3 registrations and reservations on disks for purposes of I/O fencing. In the event of a split-brain condition, I/O fencing allows only a system with a valid registration to write to a disk. Thus, I/O fencing prevents data corruption on the disks.
System administrators can use the -a, -m, -n, -x, -p, -s, and -r flags to validate the accessibility of the disks and to perform troubleshooting tasks; these options do not actually implement fencing
A disk_filename contains the list of all disks and each path (in the event of multiple paths) in a disk group.
Note: While using -x and -p options, make sure I/O fencing is not configured; these options will overwrite valid keys used by VxVM.
If administrators use the -p, -a, -m, -n, or -x options, the key is 8-bytes whatever the user supplies. Administrators can use the utility to display state information, registration and reservation information, and key definitions. The vxfenadm utility supports both character and numeric key formats.
Character Key Format
key is a character string. If key is less than 8 bytes in length, then vxfenadm will append it with - (hyphen).
For keys shorter than 8 bytes, use -K KEY where KEY is in the numeric (ascii value) format.
Numeric Key Format
KEY is in numeric (ascii value) format. For example, the equivalent numeric format for the key APGR000 is 65,80,71,82,48,48,48,0. Because the key is seven bytes long, 0 is used for the eighth byte.
-k The key consisting of eight bytes defined for this set of disks. -K Same as -k, but in numeric sequence. -f Option flag preceding the name of the file, disk_filename, that contains all of the fully qualified path(s) to each disk; a disk can be accessible by multiple paths. -p Removes the registrations and reservations made for disks in disk_filename made with key used by the victim node (-v victim_node_key). -v Key used by the victim node to register/reserve disks. -a Registers with the disks in disk_filename using RegisterIgnore operation. -m Registers with the disks in disk_filename. -n Reserves with the disks in disk_filename. -x Unregisters with the disks in disk_filename. -s Reads the keys registered on a disk specified by diskpath or reads the keys which are registered in all disks listed in disk_filename. Keys are displayed in numeric, character and node format. -g Reads the keys registered on a disk specified by diskpath or reads the keys which are registered on all disks listed in disk_filename. Keys are displayed in numeric and character format. -G Reads the keys on a disk and if possible prints node ID based on first byte of the key. Specify a diskpath or a disk_filename (a listing of paths), and print formatted results. -r Reads the reservations on a disk specified by diskpath or reads the reservations on all disks listed in disk_filename. -R Reads the reservations on a disk specified by diskpath or reads the reservations on all disks listed in disk_filename, and print the results in numeric format. -c Clears persistent reservations done by all nodes on disks mentioned in disk_filename. For this command to be successful, the node where this command is run must have its key registered with all disks in disk_filename. -i Reads the SCSI inquiry information from the disk listed in diskpath. -t Issue SCSI TEST UNIT command and return 0 if successful. -d Displays cluster-wide system state. -h Displays the usage for vxfenadm command.
If you enter the following command to register a key AVCS:
# vxfenadm -m -k AVCS -f disk_filename
-k AVCS will convert the key to AVCS---- before the SCSI-3 command is issued to the device. AVCS will register as AVCS---- on the disk. The same holds for other SCSI-3 commands. If you try to unregister a key with character format that is less than 8 bytes, the unregistration fails. For example: Read the keys registered on a disk using the following command:
# vxfenadm -g all -f disk_filename Device Name: <diskpath> Total Number Of Keys: 2 key: Key Value [Numeric Format]: 65,80,71,82,48,48,48,0 Key Value [Character Format]: APGR000
If you unregister the key using the following command, the unregistration fails:
# vxfenadm -x -k APGR000 -f disk_filename VCS FEN vxfenadm ERROR V-11-2-1204 Command 0 FAILED for:diskpath VCS FEN vxfenadm ERROR V-11-2-1120 Unregistration FAILED for:diskpath VCS FEN vxfenadm ERROR V-11-2-1133 Error returned
In this case, the key registered on the disks is APGR000. But the vxfenadm command implicitly converted the key to APGR000-. Hence the unregistration failed. The unregistration will succeed with the numeric format.
To successfully unregister the key, enter the following command:
# vxfenadm -x -K 65,80,71,82,48,48,48,0 -f disk_filename VCS FEN vxfenadm NOTICE Deleted the key:[APGR000] from device diskpath
To clear all reservations on a disk, enter the following command at a node having reservation on the disk:
# vxfenadm -c -k VF000001 -f disk_filename DMP Clear completed for disk path: disk_path
vxfenconfig(1M), vxfentsthdw(1M), vxfendebug(1M), vxfenmode(4M), vxfenclearpre(1M)
Copyright (c) 2011 Symantec.
All rights reserved.
|VCS 6.0||VXFENADM (1M)|