A replacement disk should have the same disk geometry as the disk that failed. That is, the replacement disk should have the same bytes per sector, sectors per track, tracks per cylinder and sectors per cylinder, same number of cylinders, and the same number of accessible cylinders.
You can use the prtvtoc command to obtain disk information.
The removal and replacement of a disk in a Sun StorEdgeTM A5x00 or similar type of array, requires a different procedure.
If failures are starting to occur on a disk, but the disk has not yet failed completely, you can replace the disk. This involves detaching the failed or failing disk from its disk group, followed by replacing the failed or failing disk with a new one. Replacing the disk can be postponed until a later date if necessary.
If removing a disk causes a volume to be disabled, you can restart the volume so that you can restore its data from a backup.
See the Storage Foundation High Availability Solutions Troubleshooting Guide.
To replace a disk
Enter disk name [<disk>,list,q,?] mydg02
VxVM NOTICE V-5-2-371 The following volumes will lose mirrors as a result of this operation: home src No data on these volumes will be lost. The following volumes are in use, and will be disabled as a result of this operation: mkting Any applications using these volumes will fail future accesses. These volumes will require restoration from backup. Are you sure you want do this? [y,n,q,?] (default: n)
To remove the disk, causing the named volumes to be disabled and data to be lost when the disk is replaced, enter y or press Return.
To abandon removal of the disk, and back up or move the data associated with the volumes that would otherwise be disabled, enter n or q and press Return.
For example, to move the volume mkting to a disk other than mydg02, use the following command.
The ! character is a special character in some shells. The following example shows how to escape it in a bash shell.
# vxassist move mkting \!mydg02
After backing up or moving the data in the volumes, start again from step 1.
The following devices are available as replacements: c0t1d0 You can choose one of these disks now, to replace mydg02. Select none if you do not wish to select a replacement disk. Choose a device, or select none [<device>,none,q,?] (default: c0t1d0)
Do not choose the old disk drive as a replacement even though it appears in the selection list. If necessary, you can choose to initialize a new disk.
You can enter none if you intend to replace the physical disk.
VxVM NOTICE V-5-2-285 Requested operation is to remove mydg02 from group mydg. The removed disk will be replaced with disk device c0t1d0. Continue with operation? [y,n,q,?] (default: y)
vxdiskadm displays the following messages to indicate that the original disk is being removed:
VxVM NOTICE V-5-2-265 Removal of disk mydg02 completed successfully. VxVM NOTICE V-5-2-260 Proceeding to replace mydg02 with device c0t1d0.
The disk c1t0d0 was a previously encapsulated root disk. Due to the disk layout that results from root disk encapsulation, the preferred action is to reinitialize and reorganize this disk. However, if you have any non-redundant data on this disk you should not reorganize this disk, as the data will be lost. Reorganize the disk? [y,n,q,?] (default: y) y
Entering y at the prompt destroys any data that is on the disk. Ensure that you have at least one valid copy of the data on other disks before proceeding.
Enter the desired format [cdsdisk,sliced,simple,q,?] (default: cdsdisk)
Enter the format that is appropriate for your needs. In most cases, this is the default format, cdsdisk.
Enter desired private region length [<privlen>,q,?] (default: 65536)
Use FMR for plex resync? [y,n,q,?] (default: n) y vxdiskadm displays the following success message: VxVM NOTICE V-5-2-158 Disk replacement completed successfully.
Remove another disk? [y,n,q,?] (default: n)
It is possible to move hot-relocate subdisks back to a replacement disk.