vxdisksetup, vxdiskunsetup - configure a disk for use with Veritas Volume Manager
/etc/vx/bin/vxdisksetup [-ief] disk_address [attribute...]
/etc/vx/bin/vxdisksetup [-if] disk_address format=cdsdisk [attribute...]
/etc/vx/bin/vxdisksetup [-if] disk_address format=simple [attribute...]
/etc/vx/bin/vxdisksetup [-ief] disk_address format=sliced [attribute...]
/etc/vx/bin/vxdiskunsetup [-C] disk_address...
The vxdisksetup command configures the disk for use by Veritas Volume Manager (VxVM). vxdisksetup is called by the vxdiskadd command as part of initial disk configuration. It is not typically necessary to call this command directly.
Note In release 4.0 of VxVM, the behavior of the vxdisksetup command has been changed so that it only creates auto-configured disks (with a disk access type of auto; see vxdisk(1M)), which can have one of the following formats:
The disk is formatted as a CDS disk that is suitable for moving between different operating systems. This is the default format for non-EFI disks (provided that the -i option is used to write the disk header). It is not suitable for boot disks or EFI disks.
Note As the CDS format is applied to the entire disk and is unsuitable for boot disks, options and attributes that relate to partitions, slices or booting are not applicable. The CDS format is also incompatible with EFI disks.
The disk is unformatted.
Note This value may be displayed, but it cannot be set as a valid format.
The disk is formatted with a single partition, which contains the private region that VxVM uses to store configuration information, followed by a public region from which subdisks can be allocated.
The disk is formatted with separate partitions for the private and public regions. VxVM uses the private region partition to store configuration information, and allocates subdisks from the public region partition. This format can be applied to disks that can be used to boot the system. If the disk is not initialized as a boot disk, space is reserved on the disk to allow it to be converted to cdsdisk format if required.
The sliced format is the default for EFI disks.
The vxdiskunsetup command reverses the configuration done by vxdisksetup and makes the specified disks unusable by VxVM. vxdiskunsetup can be applied only to VxVM-initialized disks that are not in use within an imported disk group.
The disk_address argument passed to vxdisksetup or to vxdiskunsetup directs the command to the device that corresponds to the disk being operated upon. The name must reference a valid disk with partition devices under the /dev/vx/rdmp directory.
The vxdiskunsetup command operates by removing the public and private regions that were created by the last invocation of vxdisksetup on the specified disks. After this operation, those disks are converted from the online to the online invalid (as displayed by vxdisk list).
The /etc/default/vxdisk file can be used to set the default values of the format and privlen attributes for the vxdisk and vxdisksetup commands. Values in this file override inbuilt values, and may themselves be overridden by values specified on the command line. For details, see the vxdisk(1M) manual page.
vxdiskunsetup usually does not operate on disks that appear to be imported by some other host (for example, a host that shares access to the disk). In this case, the -C option can be specified to force de-configuration of the disk, effectively removing the host locks that were detected by vxdiskunsetup.
Allocates the private region at the end of the disk.
Note This option is not supported for cdsdisk and simple format disks.
Forces a disk to be initialized even if it is a member of a deported disk group.
Writes a disk header to the disk, initializes the private region of the disk and makes the disk directly usable (as a new disk in a disk group, for example).
Note A disk that is a member of an imported disk group cannot be initialized. The command also fails if the disk is a member of a deported disk group. The -f option can be used to override the latter restriction.
You can specify attributes to affect the layout strategy used by vxdisksetup.
CAUTION: Take great care when using these attributes as they can render a disk unusable by VxVM.
Sets up kernel logs or configuration databases on the disk. This attribute has the opposite effect to the noconfig attribute. This is the default behavior if the -i option is specified. Otherwise, the attribute is ignored.
Prevents setting up kernel logs or configuration databases on the disk. The size of the default private region is set to 160 blocks, which is the minimum allowed private region size. noconfig is ignored unless the -i option is specified.
Do not reserve space for conversion to other formats such as cdsdisk.
Specifies the length of the private region of the disk. The default size of this area is 32MB. The maximum possible size of the private region is 524288 blocks.
If the -i option is not specified for a sliced format disk, an additional 256 blocks are also reserved. If the -i option is specified, the value of privlen is set to the size of the private region minus 256 blocks and minus the value of the private region offset. The reserved space allows for later conversion to the cdsdisk format.
For cdsdisk format disks, privlen is silently rounded up to the nearest multiple of 8KB if it is not already a multiple of 8KB.
Specify the partition number for the private region.
Indicates the sector offset of the private region on the disk. The default offset for the private area is at the beginning of the disk. A negative offset relocates the private region at an offset relative to the end of the disk.
An additional 256 blocks of disk space (rounded up to the nearest cylinder boundary) are reserved at the beginning of the private region unless this is overridden by the value of privoffset. The reserved space allows for later conversion to the cdsdisk format.
For the simple format, the specified value of privoffset is also rounded up to the nearest cylinder boundary.
For cdsdisk format disks, privoffset is silently rounded up to the nearest multiple of 8KB that is larger than or equal to 128KB if it is not already a multiple of 8KB or if its value is less than 128KB.
Specifies the length of the public region of the disk. This defaults to the size of the disk minus the private area on the disk.
For cdsdisk format disks, publen is silently rounded up to the nearest multiple of 8KB if it is not already a multiple of 8KB.
Sets the offset on the disk where the public region starts. By default, this is past the end of the private region.
For the sliced format, 256 blocks of disk space (rounded up to the nearest cylinder boundary) are reserved at the beginning of the public region unless this is overridden by the value of puboffset. The reserved space allows for later conversion to the cdsdisk format.
For the simple format, 256 blocks of disk space are reserved at the end of the private region unless this is overridden by the value of puboffset. The reserved space allows for later conversion to the cdsdisk format.
For cdsdisk format disks, puboffset is silently rounded up to the nearest multiple of 8KB if it is not already a multiple of 8KB.
Specify the partition number for the public region.
To initialize a disk for regular use, enter:
/etc/vx/bin/vxdisksetup -i sdc
To initialize a disk for normal use, but set the private region size to 1MB instead of the default size of 32MB, enter:
/etc/vx/bin/vxdisksetup -i sdc privlen=1m
Force deconfiguration of a VxVM-initialized disk, sdf:
/etc/vx/bin/vxdiskunsetup -C sdf
The default private region size increased from 1MB to 32MB in release 5.0.
Defaults file used by the vxdisk and vxdisksetup utilities.
vxcdsconvert(1M), vxdisk(1M), vxdiskadd(1M), vxintro(1M)